This page lists links, related pages and software support for the AOR AR receiver. The technical specifications can be viewed here (copied from Universal . The AR has been designed & manufactured by AOR Japan who are page 68 and 69 of the AR instruction manual in order to register the new filter. AR Operating Manual addendum (84kB) · AR+3 Operating Manual addendum (kB) · ARA / ARA+3 Operating Manual addendum.

Author: Kigagore Zulkibar
Country: Sri Lanka
Language: English (Spanish)
Genre: Sex
Published (Last): 16 July 2004
Pages: 327
PDF File Size: 16.76 Mb
ePub File Size: 12.45 Mb
ISBN: 640-3-84110-428-8
Downloads: 45155
Price: Free* [*Free Regsitration Required]
Uploader: Tegar

The only distinguishing feature between the two leads, is that one lead has a grey wire and the other has a purple wire within its multi-cable.

Retrospective and free updates are NOT available. The audio stage of the AR is configured to emphasise this windowhowever the centre frequency may be changed to suit personal preferences or specific requirements. Introduction 2 Introduction 13 Frequency Pass The detector output can ar500 taken from pin 9, IC8.

This antenna switch module adds antenna inputs 3 and 4 N type with control selection from the receiver. The last entered frequency in VFO may be lost.

Link all three search banks to form a single group Output N plug is to Antenna input 1 of AR Page 21 VFO mode. To print the manual completely, please, download it. To complete the data entry press [ENT] for more than one second. Frequency Offset See above Example of display: In practice however you will probably not notice any change and we recommend that they are left as standard. Got it, continue to print.


AOR AR5000 Operating Manual

Termination can be made at an additional suitable socket of one of the ones already fitted can be utilised if it is not being used possibly After that the tuning speed remains the same regardless of how much faster the encoder is rotated.

The following commands are required to do this: The reset switch is located at the top of the slot about 10mm behind the front panel. Add to my manuals Add. It is possible to add text at present at this time. MHz bandwidth Manual version 1. Various points are provided on the IF board which are intended as test points but can easily be soldered to in order to obtain an I.


Scanning A Memory Bank Note: Wiring order for this is: Note that there is a small DC level present on this pin and some DC decoupling will be needed if none is present in the decoder input. Wideband passive vertical omni directional antenna covering 30 kHz to 2 GHz. Repeat the process outlined in 3 for the third search bank, in this example bank 3 but use a step adjust value of If nothing were displayed to show that Cyber Search was in operation and no transmissions were encountered, the AR may otherwise look like it was doing nothing.

Maunal the encoder and test your work.

In particular it has been reported that the ‘clicks’ are most noticeable when the AR is tuned across the following frequency boundaries: The squelch will open every kHz approx. AR Bulletin Page AR brief production history The AR first appeared inthe serial numbers were 5xxxx six digit numbers starting with the mamual five. Switch the receiver off unplug the power cord if necessary to power down the receiver.


AOR AR Scanner ReceiverTechnical Information Page

If problems are experienced, then the solution will probably be direct connection to the FM detector IC on the IF unit.

Controls for operation are located on the front of the Display of operational information is provided via a high cabinet with connections to the rear. If this key is accidentally pressed, it may give the 0.

The AR will switch-on automatically once per day presuming the receiver had been switched off on a daily basis at the In this instance the path of feeder is i. To accept the input and complete the process, press in either of the two menus. Since writing the above Octobera third type of cable has been supplied.

Reducing the time to 4 seconds produced 96 steps 3 s 81 steps 2 s 76 steps 1 s 40 steps 0. Further aerials may be connected using the optional aerial switching unit AS with switching data being fed from a rear panel accessory socket ACC 2.

The output can be taken by directly soldering a wire to the output pin or from the capacitor it feeds C88 – located directly next to pin 9.